Utility Requirements

  • Exterior dimensions (w x h x l)42 x 80 x 32-5/8” (1067 x 2032 x 829 mm)
  • Chamber capacity (w x h x l)24 x 26 x 24” (610 x 660 x 610 mm)
  • Load Height 31” (787 mm) above finished floor
  • Steam heated units; Optional 208,240 or 480v 3-phase & 120v receptacle for control system.
  • Electrically heated units; 480v 3-phase only & 120v for control control system. Air (for pneumatic doors)
  • 1/8” NPT, 65 to 125 dynamic psig
  • Hot water; 1/2” NPT, 15 dynamic to 50 static psig, 110F (43C) maximum. Minimum flow rate 5.5 U.S. gpm, maximum flow rate 9.3 U.S. gpm.
  • Cold Water; 1/2” NPT, 30 to 50 dynamic static psig, 60F maximum. Minimum flow rate; 10.3 U.S. gpm, maximum flow rate 12.9 U.S. gpm.
  • Pure Water; 1/2” NPT, 5 dynamic to 25 static psig, minimum flow rate 5.6 U.S. gpm.
  • Steam (steam-heated units only); 1/2”NPT , 30 to 80 dynamic psig. 185-400lbs/hr. Peak flow rate 210-470 lbs/hr, maximum 90 psig static.
  • Drain; 2” NPT; a 4” O.D. floor sink style open drain.

Solution Graphics
Pay By Credit Or Debt Card
-Pay By Credit Card-
Proceed To Checkout And Enter Your Credit Card Information In Step 2

Pay By Credit Or Debit Card
To Order By Phone Call
Mon thru Fri 8:00am To 4:30 pm Central Time


Don't Take Our Word For It.....

AllClaveParts.com - Real Help With Your Autoclave Repair When You Need It

"My Statim 2000 stopped working.

Benco dental came down and said the thermal fuse and computer board was bad

Real Problems Solved By Dr Gorenburg With AllClaveParts help

Wally, thank you and your company for providing great customer service and all the help I needed to fix my autoclave.
Clearview Medical.com

Dr Haruki & Son

My tech told me my STATIM 2000 repair could either be about $350 (if it was only the thermal fuse) or up to $1500 if it was another problem.

Craig Haruki DDS
Lihue, HI

Dr Whitehouse Loves AllClaveParts.com
" It was a pleasure working with Wally who saved me thousands over what I would have had to pay when the Patterson tech......"

Dr Joseph Whitehouse
Castro Valley, CA
Create A Smile

Dr Steve Says Midmark Told Him To Throw It Away, But AllClaveParts Showed Him How To Fix It Well, that same autoclave is once again working like a champ thanks to allclaveparts.com.

Steve Douglas, DDS
Indianapolis, IN


Call Wally at AllClaveParts.com first before your local repairma

My Tuttnauer 2540M autoclave quit building up pressure. A new gasket did not solve the problem. The dental repairman said that three of the four...

Very Satisified

Wally helped me to quickly diagnose an issue and provided the part to resolve it. Much more efficient than sending the whole unit out for servicing....

I wish I would have known about you sooner

I wanted to thank you for help me fix my Midmark M11. Just like the other testimonials, a local authorized technician was going to charge $95 each...

I will be back as needed

I will be back as needed

Awesome site, you just saved me a ton with your detailed troubleshooting section and ordered the right part for repair. I appreciate it!!!! I will be...

Thanks a lot Wally for your help and training

Thanks a lot Wally for your help and training

I found this page hoping to find the parts I needed to fix my Autoclave and found not only what I needed but a great customer service, particularly...

Specials  [more]

$517.97  $489.87
Save: $28.10 off
Parse Time: 0.343 - Number of Queries: 225 - Query Time: 0.0809164359436

Check Out Our Specials

A Best Seller
Click Here To Check Out Everything On Sale