(image for) OCM HEATING ELEMENT (Element Length: 11.5 Inches)

OCM HEATING ELEMENT (Element Length: 11.5 Inches)

Model: PCH024-028

$94.97

Description

Guaranteed Quality Pelton Crane OCM Autoclave Repair Parts

Part #PCH024-028
OEM Part #014601

HEATING ELEMENT

  • 1250W, 120VAC, ~12ohms
  • Sheathing: Electrogalvanized Sheet Steel
  • Includes Heating Element, Hardware, and (3 ft) 14 AWG White Wire-High Temp Part #RPW086-2636
  • Heater Has Flip-Up Tab To Mount Overtemp Switch Part #PCT042-058 (OEM Part #004108)

Fits: Chamber
Tech Tip: Pelton Crane Recommends The Overheat Thermostat be replaced any time 1 or more heating elements are replaced.

Model(s) This Part Fits: Pelton Crane OCM Autoclave

Be sure to order the right Heating Element. Measure the Length Before Ordering. This Element is 11 1/2 Inches Long (If your element measures 10.25 inches, this is the element you need: PCH048-029


Be sure to order the right Heating Element. Measure the Length Before Ordering. This Element is 10.25 Inches Long (If your element measures 11 1/2 inches, this is the element you need: PCH024-028 (Pelton Crane Part #014601)

NEW: Too Hard to Get To The Bottom Heating Element To Measure it? Now You Can Simply (and Easier) Measure the Distance Between The Terminals on The Heating Element

Measure the distance between the terminals on the heating elements


Click Here For Installation Instructions

How To Test The Pelton Crane OCM Heating Elements

The Pelton Crane OCM Autoclave has 3 Heating Elements. While The Center Heating Element (the heating element on the bottom of the chamber) is the most common to fail, be sure to check all 3

This test consists of measuring the amount of resistance in the element. To do this, first, turn the autoclave off and unplug it from the wall
 
WARNING: CURRENT MUST NOT BE PRESENT WHEN MEASURING RESISTANCE

Set your volt/ohm meter on 200 ohms (200 NOT 200k). The ohms range is located within the Omega Ω (look for this symbol) section of your meter. It is also the area with "k" ranges (ie: 2000k,. 200k, 20K and then 2000, 200).

Place a probe from the volt/ohm meter on each of the 2 terminals on the element (it really doesn't matter which color probe goes where).

For the heating element to be good, it must fall within the resistance range in this table (between 10.800 ↔ 13.2000 ohms) If your reading is outside of this range, then it is defective and needs to be replaced.
Model Volts Watts Amps Resistance Resistance Range
Pelton Crane OCM 120v 1250 Watts 10.4167 amps ~12.00 Ohms Between 10.8000 13.2000 ohms


If you find one or more of the Pelton Crane OCM Heating Element(s) Are Defective, do not try to replace them until you have the new one(s) on hand.
The installation goes much smoother & faster when you can disconnect from the old heating element and immediately make the same connections to the new

Autoclave Repair Tip
When Replacing a Fiber Heating Element with the Newer Steel Jacketed Heating Element
Here is what you need to know

If the autoclave repair you are performing on your Pelton Crane OCM involves replacing the heating element, and the old heating element is made of a fiber material instead of encased in a steel jacket, you will need to make sure you remove the Copper Plate that is with the old element

To avoid confusion, note that the Copper Plate is not copper in color, nor is it the familiar green of copper as it weathers.

Instead, it will be black as shown in the picture below

OCM Copper Plate

Failure to remove this Copper Plate will result in a short, so make sure you remove and discard it before installing the new heating element!

The finished sequence of parts are:

  1. The Stainless Steel Bands (looks like big hose clamps)
  2. The Steel Bracket that the Heating Element Rests On
  3. The Heating Element - Flat Against the Chamber

"Pelton Crane OCM Autoclave Repair Made Simple™"

Fast Delivery

We usually ship the same day! All packages are shipped w/Delivery Confirmation.

100% Secure Payment

Your transaction is secure thanks to the PayPal payment system: SSL (Secure Socket Layer).

Shopper Award
(image for) AllClaveParts Payment Methods

Customers who bought this product also purchased...

allclaveparts.com widget logo