Add to Cart:

  • Description
  • Info & Guide
  • Specs
  • Reviews
All of the Pelton Crane Magnaclave Replacement Parts We Offer Are Fully Guaranteed

Part #PCH092-283
Pelton Crane Part #004503

  • 500W
  • 240VAC
  • ~115ohms
  • Terminal Hardware
Fits: Chamber

Model This Part Fits: All Pelton Crane Magnaclaves

Also Available

How To Test Pelton Crane Magnaclave Wall Heater Strip

This test consists of measuring the amount of resistance in the element. To do this, first, turn the autoclave off and unplug it from the wall


Set your volt/ohm meter on 200 ohms (200 NOT 200k). The ohms range is located within the Omega (Ω )(look for this symbol) section of your meter. It is also the area with "k" ranges (ie: 2000k,. 200k, 20K and then 2000, 200).

Place a probe from the volt/ohm meter on each wire where it connects to the element (it really doesn't matter which color probe goes where) and check your reading

For the heating element to be good, it must fall within the resistance range in this table (between 103.5 and 126.5 ohms) If your reading is outside of this range, then it is defective and needs to be replaced.
Model Volts Watts Amps Resistance Resistance Range
Magnaclave Wall Heater Strip
240 vac 500 2.0833 amps ~115 Ohms 103.5 ↔ 126.5 ohms

How To Replace The Magnaclave Wall Heater Strip

  1. Remove the old heater in normal fashion
  2. Inspect and clean outside of chamber
  3. Install new heaters, making sure that contact between heater and chamber is evenly distributed. CAUTION: To assure no burnouts due to hot spots:
    • Chamber surface is dry and smooth
    • Contact of heater to chamber is completely even and uniform
  4. Sequentially tighten tie down bands. The same amount of torque should be applied to all four bands (40 in. lbs.)
  5. Perform final inspection. Verify that the curvature of the heaters matches the chamber and no gaps exist. Allow 10-15 minutes "burn-in" time.
Warning: Excessive tightening of nuts may cause heater to fail

There are currently no any reviews about this product.

Customer Reviews
Solution Graphics
Pay By Credit Or Debt Card
-Pay By Credit Card-
Proceed To Checkout And Enter Your Credit Card Information In Step 2

Pay By Credit Or Debit Card
To Order By Phone Call
Mon thru Fri 8:00am To 4:30 pm Central Time


Don't Take Our Word For It.....

Customer Reviews - Real Help With Your Autoclave Repair When You Need It

"My Statim 2000 stopped working.

Benco dental came down and said the thermal fuse and computer board was bad

Real Problems Solved By Dr Gorenburg With AllClaveParts help

Wally, thank you and your company for providing great customer service and all the help I needed to fix my autoclave.

Dr Haruki & Son

My tech told me my STATIM 2000 repair could either be about $350 (if it was only the thermal fuse) or up to $1500 if it was another problem.

Craig Haruki DDS
Lihue, HI

Dr Whitehouse Loves
"It was a pleasure working with Wally who saved me thousands over what I would have had to pay when the Patterson tech......"

Dr Joseph Whitehouse
Castro Valley, CA
Create A Smile

Dr Steve Says Midmark Told Him To Throw It Away, But AllClaveParts Showed Him How To Fix It Well, that same autoclave is once again working like a champ thanks to

Steve Douglas, DDS
Indianapolis, IN

Parse Time: 0.362 - Number of Queries: 248 - Query Time: 0.152306183838

Check Out Our Specials

A Best Seller
Click Here To Check Out Everything On Sale