OCR HEATING ELEMENT


$82.97

Add to Cart:


  • Description
  • Info & Guide
  • Specs
Guaranteed High Quality Pelton Crane OCR Autoclave Repair Parts

Part #PCH023-103
Pelton Crane Part #014603

HEATING ELEMENT
  • 1600W, 120V, ~9ohms
  • Sheathing: Electrogalvanized Sheet Steel
  • ~15" Long
  • Includes Heating Element, Hardware, and ~ (3 ft) 14 AWG White High Temperature Wire Part #RPW086-2636
  • Heater has flip-up tab to mount Overtemp Switch Part #PCT042-135
Fits: Chamber
Pelton Crane Recommends The Overheat Thermostat Part #PCT042-135 be replaced any time 1 or more heating elements are replaced.

Click Here To Learn How To Install The New Heating Element(s)

Tech Tip: Be sure your Pelton Crane OCR heating element is defective before replacing it, by performing the following test:

How To Test The Pelton Crane OCR Heating Elements

This test consists of measuring the amount of resistance in the element. To do this, first, turn the autoclave off and unplug it from the wall

WARNING: CURRENT MUST NOT BE PRESENT WHEN MEASURING RESISTANCE.

Set your volt/ohm meter on 200 ohms (200 NOT 200k). The ohms range is located within the Omega (Ω )(look for this symbol) section of your meter. It is also the area with "k" ranges (ie: 2000k,. 200k, 20K and then 2000, 200).

Place a probe from the volt/ohm meter on each terminal of the 2 terminals on the element (it really doesn't matter which color probe goes where)

While the center heating element is the most common to wear out, be sure to test all three

For the heating element to be good, it must fall within the resistance range in this table (between 8.10 and 9.90 ohms) If your reading is outside of this range, then it is defective and needs to be replaced.
Model Volts Watts Amps Resistance Resistance Range
Pelton Crane OCR
120v 1600Watts 13.333 amps ~9.00 Ohms 8.10 9.90 ohms




Autoclave Repair Tip
When Replacing a Fiber Heating Element on The OCR with the Newer Steel Jacketed Heating Element
Here is what you need to know

If the autoclave repair you are performing on your Pelton Crane OCR involves replacing the heating element, and the old heating element is made of a fiber material instead of encased in a steel jacket, you will need to make sure you remove the Copper Plate that is with the old element


To avoid confusion, note that the Copper Plate is not copper in color, nor is it the familiar green of copper as it weathers.


Instead, it will be black as shown in the picture below


OCM Copper Plate

Failure to remove this Copper Plate will result in a short, so make sure you remove and discard it before installing the new heating element!


The finished sequence of parts are:

  1. The Stainless Steel Bands (looks like big hose clamps)
  2. The Steel Bracket that the Heating Element Rests On
  3. The Heating Element - Flat Against the Chamber



Customer Reviews
Solution Graphics
Pay By Credit Or Debt Card
-Pay By Credit Card-
Proceed To Checkout And Enter Your Credit Card Information In Step 2

Pay By Credit Or Debit Card
To Order By Phone Call
636-390-2792
Mon thru Fri 8:00am To 4:30 pm Central Time

Testimonials

Don't Take Our Word For It.....


Customer Reviews


AllClaveParts.com - Real Help With Your Autoclave Repair When You Need It

"My Statim 2000 stopped working.

Benco dental came down and said the thermal fuse and computer board was bad

Real Problems Solved By Dr Gorenburg With AllClaveParts help

Wally, thank you and your company for providing great customer service and all the help I needed to fix my autoclave.
Clearview Medical.com

Dr Haruki & Son

My tech told me my STATIM 2000 repair could either be about $350 (if it was only the thermal fuse) or up to $1500 if it was another problem.

Craig Haruki DDS
Lihue, HI


Dr Whitehouse Loves AllClaveParts.com
"It was a pleasure working with Wally who saved me thousands over what I would have had to pay when the Patterson tech......"

Dr Joseph Whitehouse
Castro Valley, CA
Create A Smile


Dr Steve Says Midmark Told Him To Throw It Away, But AllClaveParts Showed Him How To Fix It Well, that same autoclave is once again working like a champ thanks to allclaveparts.com.

Steve Douglas, DDS
Indianapolis, IN
stevedouglasddspc.com


Parse Time: 0.431 - Number of Queries: 276 - Query Time: 0.164083715088
Content

Check Out Our Specials


A Best Seller
Click Here To Check Out Everything On Sale