Shopping
Autoclave Maintenance
Autoclave Parts
Autoclave Troubleshooting
Dental Equipment Parts
MEDIVATORS
Videos and Animations
EXAM TABLES & CHAIRS
Case Studies
Free Technical Support
Autopsy Saw Parts
Infant Incubators & Warmers
Lab Equipment
Ventilators
Orthopedics & Physical Therapy
Patient Cables & Leadwires
ASPIRATORS AND SUCTION PUMPS
Maintenance Guides
Operational Manuals
Maintenance Tips
Parts Installation Guides
Account Info
Log In
Create Account
Autoclave Maintenance
Tuttnauer Maintenance Guides
Statim Maintenance Guides
Autoclave Parts
Scican Statim
Midmark ® Ritter
Tuttnauer ®
Pelton Crane
Barnstead Sterilizer
Kavoklave
Midmark Ritter
NAPCO
AMSCO
PRESTIGE 2100
Ritter - Castle
Spectroline
S.S. White
Vernitron
Autoclave Cleaning Products
MDT Harvey Mediclaves
Autoclave Repair Supplies
Autoclave Repair Special Tools
Autoclave Troubleshooting
How To Test Heating Elements
NAPCO Troubleshooting
Prestige 2100
VernitronTroubleshooting
STATIM DETAILED TROUBLESHOOTING
tuttnauer temp
Statim G4 Troubleshooting
Midmark Troubleshooting
Tuttnauer Troubleshooting
STATIM TROUBLESHOOTING
Documents & Guides
Pelton Crane Troubleshooting
Troubleshooting Guides
AMSCO 3000 BASIC TROUBLESHOOTING
AMSCO 900 & 901
Delta XL Troubleshooting
Castle Table Top Troubleshooting
CHEMICLAVE 5000 TROUBLESHOOTING
Kavoklave
Steam Trap Troubleshooting
Dental Equipment Parts
Dental Chair Parts
Dental Handpieces & Parts
DENTAL ULTRASONIC SCALERS
Miscellaneous
Dental Compressor Parts
Dental Delivery Systems
Dental Film & X-Ray Processors
Dental Light Parts
Dental Vacuum Parts
Dental Water Control Parts
MEDIVATORS
Medivator CER Optima
Medivator Advantage Plus
Medivator DSD-201
Medivator DSD Edge
Medivator DSD-91E
Medivator SSD-102
More
Videos and Animations
EXAM TABLES & CHAIRS
Case Studies
Free Technical Support
Autopsy Saw Parts
Infant Incubators & Warmers
Lab Equipment
Ventilators
Orthopedics & Physical Therapy
Patient Cables & Leadwires
ASPIRATORS AND SUCTION PUMPS
Maintenance Guides
Operational Manuals
Maintenance Tips
Parts Installation Guides
About Us
Blog
Home
›
Autoclave Parts
›
Bulk Sterilizers
›
CASTLE/GETINGE
›
3525
› Midmark M7 Timer Kit Installation Guide
Midmark M7 Timer Kit Installation Guide
RCK116 TIMER KIT (30 MIN)
INSTALLATION NOTES AND TIMER WIRING DIAGRAMS
Important! Disconnect Power From Autoclave and Allow To Cool Before Servicing.
Removing the Timer Knob
On some of the earlier units, the timer knob is tightened to the unit by an Allen Screw. Before removing the knob, loosen the screw
Spacer is not needed. On some units that have the buzzer mounted on the timer, a spacer was used. Remove and discard the spacer as it is not rquired with the new timer.
It may be necessary to drill holes to mount new Timer. On some units, a nut is used to secure the timer to the front panel. On these units, it is necessary to drill two new holes on the front panel to secure the new Timer.
To begin, from the center of the shaft hole, at the 12:00 position, measure 9/16" upwards, make a mark, and center punch.
Next, at the 6:00 position from the center of the shaft hole, measure 9/16" downwards, make a mark, and center punch. At the center marks for each of the hole, drill a 3/16" hole. Use two #8-32 x 5/16" screws to secure timer
Mounting the Buzzer Assembly
Remove the top, left screw that secures the Relay Assembly to the bracket on the right side of the chamber. Position the Buzzer Assembly against the same bracket and secure the buzzer to the bracket using the same screw.
Connecting electrical leads. See Timer Wiring Diagrams and note that the #2 contact and the "B" positions are reversed on the Timer when compared to the OEM Timer.
If Wire Harness is too short. When upgrading to this newer style Timer (Part #RCT107-3406), the original wire harness may be too short. To extend the length, install the enclosed Wire Harness (Part #RCH117-3405).
Buzzer adjustments
Adjust the loudness of the buzzer by turning the adjustment screw clockwise for a softer signal or counterclockwise for a louder signal