Midmark M7 Timer Kit Installation Guide



  • Description
  • Info & Guide
  • Specs


RCK116 TIMER KIT (30 MIN)
INSTALLATION NOTES AND TIMER WIRING DIAGRAMS




Important! Disconnect Power From Autoclave and Allow To Cool Before Servicing.

Removing the Timer Knob

  • On some of the earlier units, the timer knob is tightened to the unit by an Allen Screw. Before removing the knob, loosen the screw
  • Spacer is not needed. On some units that have the buzzer mounted on the timer, a spacer was used. Remove and discard the spacer as it is not rquired with the new timer.
  • It may be necessary to drill holes to mount new Timer. On some units, a nut is used to secure the timer to the front panel. On these units, it is necessary to drill two new holes on the front panel to secure the new Timer.


    • To begin, from the center of the shaft hole, at the 12:00 position, measure 9/16" upwards, make a mark, and center punch.


    • Next, at the 6:00 position from the center of the shaft hole, measure 9/16" downwards, make a mark, and center punch. At the center marks for each of the hole, drill a 3/16" hole. Use two #8-32 x 5/16" screws to secure timer


Mounting the Buzzer Assembly

  • Remove the top, left screw that secures the Relay Assembly to the bracket on the right side of the chamber. Position the Buzzer Assembly against the same bracket and secure the buzzer to the bracket using the same screw.
  • Connecting electrical leads. See Timer Wiring Diagrams and note that the #2 contact and the "B" positions are reversed on the Timer when compared to the OEM Timer.
  • If Wire Harness is too short. When upgrading to this newer style Timer (Part #RCT107-3406), the original wire harness may be too short. To extend the length, install the enclosed Wire Harness (Part #RCH117-3405).


Buzzer adjustments

  • Adjust the loudness of the buzzer by turning the adjustment screw clockwise for a softer signal or counterclockwise for a louder signal

This product was added to our catalog on Sunday 24 January, 2010.



Customer Reviews
Solution Graphics
Pay By Credit Or Debt Card
-Pay By Credit Card-
Proceed To Checkout And Enter Your Credit Card Information In Step 2

Pay By Credit Or Debit Card
To Order By Phone Call
636-390-2792
Mon thru Fri 8:00am To 4:30 pm Central Time

Testimonials

Don't Take Our Word For It.....


Customer Reviews


AllClaveParts.com - Real Help With Your Autoclave Repair When You Need It

"My Statim 2000 stopped working.

Benco dental came down and said the thermal fuse and computer board was bad

Real Problems Solved By Dr Gorenburg With AllClaveParts help

Wally, thank you and your company for providing great customer service and all the help I needed to fix my autoclave.
Clearview Medical.com

Dr Haruki & Son

My tech told me my STATIM 2000 repair could either be about $350 (if it was only the thermal fuse) or up to $1500 if it was another problem.

Craig Haruki DDS
Lihue, HI


Dr Whitehouse Loves AllClaveParts.com
"It was a pleasure working with Wally who saved me thousands over what I would have had to pay when the Patterson tech......"

Dr Joseph Whitehouse
Castro Valley, CA
Create A Smile


Dr Steve Says Midmark Told Him To Throw It Away, But AllClaveParts Showed Him How To Fix It Well, that same autoclave is once again working like a champ thanks to allclaveparts.com.

Steve Douglas, DDS
Indianapolis, IN
stevedouglasddspc.com


Parse Time: 0.276 - Number of Queries: 220 - Query Time: 0.117836573502
Content

Check Out Our Specials


A Best Seller
Click Here To Check Out Everything On Sale