Shopper Award
AllClaveParts
Statim 2000 WATER PUMP KIT (OLDER VERSION )

Statim 2000 WATER PUMP KIT (OLDER VERSION )

(3) 5 out of 5 stars
Model: SCP050-6209

$250.97

Guaranteed High Quality Statim Water Pump

Part #SCP050-6209
Statim Part #01-100568s (Invensys Pump - StatIM 2000)

WATER PUMP KIT


Specifications

  • 120Volts, 60Hz.
  • This Invensys brand pump will accommodate StatIM 2000 Sterilizers with PCB Software Rev. 6.3 or older only
  • See Notes below

Includes:

Fits: Chassis
Model This Part Fits: Statim 2000 Autoclaves with PCB Software Rev. 6.4 or older only

 

Make Sure You Order The Right Water Pump for Your Statim Autoclave

Note: Even though the software version usually indicates which water pump is installed in the Statim Autoclaves, we have run into many instances where it is not accurate. Here is a surer way to make sure you get the pump you need

Be sure to look at the top of the water pump currently installed in your autoclave, and compare it with the pictures below.

 

 

 

Make Sure you order the right water pump for your statim autoclave


If you have the Older Version with the Over Heat Thermostat as shown in the picture above, then this is the Water Pump You Need

But if you have the Newer Version without the Over Heat Thermostat as shown in the picture above, then click on the link below for your model for the Water Pump You Need:

 

 

Click Here For Easy To Follow Instructions On Locating Your Software Revision Number

 

 

INVENSYS VERSION PUMP (Part #SCP050-6209) for Statim 2000 Autoclaves with Software R603 and older.

 

 

 

Statim 2000 autoclaves manufactured after March 2006 were supplied with the spring clip (grounding)on the water pumps to improve water conductivity circuitry (a Water Quality Sensor)

 

 

In early 2006, Statim introduced the Reservoir Cap & Filter Part #SCK059-6380

 

 

Effective June 2007, Statim stopped using the wire mesh filter (installed in the inlet and outlet fittings) and offered the In-Line Water Filter Part #SCF034-3822 to be installed between the reservoir and pump

 

 

Statim now recommends the use of the Reservoir Cap & Filter Part #SCK059-6380 along with the In-Line Water Filter on all units. For Statim 2000 Autoclaves with the original water pump, the wire mesh filters should be removed and the autoclave should be upgraded to the In-Line Water Filter Drain Kit with Pump Filter Part #SCK037-4013


Also available:

 

(3) 5 out of 5 stars
See all 3 reviews Write Review
100%

Shane Verified Buyer November 23, 2015 North Carolina, United States
Wally, your personal service is great.. Will definetly recommend to anyone looking for the autoclave. I will go back to buy again. Thank you!!
Was this review helpful to you?YesNo
Share This Review

Shane Verified Buyer October 19, 2015 North Carolina, United States
Fast, easy and turned out a great finished product. Will definetly recommend to anyone looking for the autoclave. I will go back to buy again. Thank you!!
Was this review helpful to you?YesNo
Share This Review

Shane Verified Buyer April 15, 2015 North Carolina, United States
Very helpful and responsive. I will be using this store many more times in the future. Will definetly recommend to anyone looking for the autoclave. I will go back to buy again. Thank you!!
Was this review helpful to you?YesNo
Share This Review

There is no any question about this product.

Qty

Fast Delivery
We usually ship the same day! All packages are shipped w/ Delivery Confirmation

100% Secure Payment
Your transaction is secure thanks to the paypal payment system: SSL (Secure Socket Layer)

Shopper Award

AllClaveParts Payment Methods