Add to Cart:


Midmark M7 AIR VENT BELLOWS ASSEMBLY (BELLOWS STYLE)

$176.97

Midmark M7 Autoclave Repair Parts Guaranteed Quality

Part #RCB100-849
OEM Part #002-0375-00

AIR VENT BELLOWS ASSEMBLY
  • 1/4” Compression Fittings Both Ends
  • Bronze Bellows
  • Actuates Within 5°F Of Saturated Steam
  • See Notes Below For Serial Numbers This Part Fits
Fits: Reservoir Tubing

Model(s) This Part Fits: Midmark M7 Autoclave

Notes: CHECK SERIAL NUMBERS HERE:
  • Fits M7-001 thru -019 with Serial # prefixes CZ, DA, DB, DX, DY, FD & OM
  • Fits M7D-001 thru -019 with Serial # prefixes FF & FG


The Bellows Style With It's Extra Convolutions, Is Designed To Last Longer Than The Diaphragm Style


SERVICE TIP: AllClaveParts now offers two different Air Vent Bellows Assemblies – Part #RCB100-849 and RCB089-787. There are two different styles of assemblies – the diaphragm style and the bellows style. Here’s the difference

Currently, the AllClaveParts RCB089-787 and the OEM’s are both Diaphragm Style assemblies. The Diaphragm is the older style and has only one convolution doing all the work.

The other is a Bellows Style assembly – the AllClaveParts RCB100-849. This style assembly has several convolutions doing all of the work so it lasts much longer than the diaphragm style. Now you have a choice…It’s the AllClaveParts Advantage!

How To Replace The Midmark M7 Autoclave Bellows Assembly

Applies To Units With Serial Numbers CP-1000 Thru CP-1061, CR-1000 Thru CR-1113, CS-1000 Thru CS-1569, And RB-1000 Thru RB-7193)

NOTE: Older units which do not have a Serial Number prefix of CP-xxxx, CR-xxxx, CS-xxxx, or RB-xxxx were manufactured by Sybron Corp and not by Midmark.

However, a retrofit kit for the bellows assembly is available. If the unit has already been retrofitted with a Midmark style bellows, use these instructions . If not retrofitted, then you need to use the RCB002-845 (OEM Part #H284709 / 144382) Bellows Assembly

A. Removing The Midmark Bellows Assembly
  1. Remove Cover Assembly Click Here For Instructions


  2. Warning: Make sure unit is vented and cool before attempting to make repairs. Failure to do so could result in serious injury or burns.
  3. Remove tank cover (1) from tank assembly (2) (here may be a strip of tape holding the tank cover on to prevent the tank cover from vibrating and making noise)
  4. Using a wrench on bellows nut to hold bellows assembly (3) stationary, loosen and disconnect compression nut (4)
  5. Remove bellows assembly (3) from tube (5)
NOTE: This Figure shows the old-style bellows. The procedure for the new-style is the same.

Midmark M7 Bellows Assembly Installation


Installing the Midmark Bellows Assembly

  1. Position bellows assembly (3) on tube (5), making sure flow arrow is pointing away from compression nut (4)
  2. Using a wrench on bellows nut to hold bellows assembly (3) stationary, screw compression nut (4) onto bellows assembly
  3. Install tank cover (1) on tank assembly (2)
  4. Install the cover assembly
Midmark M7 Autoclave Repair Made Simple ™

  • Model: RCB100-849


This product was added to our catalog on Tuesday 18 December, 2007.

Your IP Address is: 54.82.77.50
Copyright © 2014 AllClaveParts. Powered by Zen Cart
Parse Time: 0.351 - Number of Queries: 325 - Query Time: 0.122246611664